+
Dealers Wanted
   Znen  Sport 150 Moped (ZN150T-18)       Znen 150cc Moped, Model  ZN150T-18

Znen Sport 150T-18 Seat $75

 

Znen Sport 150T-18 Front Fork Set (17 1/2 inch Long) $100

 

Znen Sport 150T-18 Left Switch (8-Pin Plug) $20


Znen Sport 150T-18 Right Switch (3-Pin Plug) $20

Znen Sport 150T-18 Right Switch (4-Pin Plug) $20

Znen Sport 150T-18 Right Speed Controller $12, Left Grip $8, Set $20

Znen Sport 150T-18 Rear Disc Rim (2.5 x 16 rim, 24 spline, 66mm eye to eye bolt spacing for rotor) $130

Znen Sport 150T-18 Front Disc Rim (2.5X16) $130

Znen Sport 150T-18 Front Disc Brake  (2-chamber version) $90

Znen Sport 150T-18 Rear Disc Brake $95

Znen Sport 150T-18 Gas Cable (79 inch) $15

Znen Sport 150T-18 Front Disc Brake  (1-chamber version) $90

Znen Sport 150T-18 Main Wire Harness $45

Znen 150T-18 Handle Bar $35

Znen Sport 150T-18 Speed Odometer Drive $20

Znen 150T-18 Front Caliper (Bolt hole spacing:97mm eye to eye measurement) $40

Znen Sport 150T-18 Wind Shield $38

Znen 150T-18 Odometer Cable (38 1/2" total length) $16

   

Znen Sport 150T-18 Front Axle (9 1/2 inch long, 12mm OD) $6, Znen Sport 150T-18 Front Axle Bushing (1 3/8 inch long) $2

Znen 150T-18 Left Hydraulic Break Lever $12

Znen 150T-18 Right Hydraulic Break Lever $12

   
Maximum Speed:  90Km/h         Fuel Capacity  1.45 gallon      Brake Type  Front Disc, Rear Drum   Engine Type  4-stroke, Single, air cooled 150cc motor.       Tire size:  100/80-16,  120/80-16    Battery  12V/9ah       Starting System  Electric/Kicks          54 mpg
AKA: Kerrigan T-150, Falcon

       

Znen Sport 150T-18 Muffler Assembly $130

Znen 150T-18 Muffler Shield $16

   

Znen Sport 150T-18 Lock $48  

Znen 150T-18 Front Head Light $79

Znen Sport 150T-18 Rear Rotor (58mm center hole, 180mm diameter, 3mm thick) $28

Znen Sport 150T-18 Front Rotor (58mm center hole, 238mm diameter, 3mm thick, Raised center) $30

Znen Sport 150T-18 Rear Shock Set (13 inch long,  Eye to eye 11 7/8 inch) $79

Znen 150T-18 Kick Stand (8 7/8inch) $15

Znen 150T18 Rear Break Light Assembly $68

 

Znen 150T-18 CVT Cover (At longest point: Total length 19 3/16 inch) $60

Znen Sport 150T-18 Odometer Gauge $65

Znen 150T-18 Left Master Cylinder W/ Chrome Lever $30

Znen 150T-18 Master Cylinder W/ Chrome Lever $30


Znen 150T-18 Front Brake Pad set $9

|| Show All Gas Scooter Parts  Page 2 | Show All Electric Scooter Parts Page 2 | Find Gas Scooter Parts by Scooter Style|   Find Electric Scooter Parts by Scooter Style|

    order@ScooterParts4Less.com|  | Order Info | ScooterParts4Less LLC |

Znen 150T-18 Left And Right Hydraulic Break Lever $24

 

Znen 150cc Rectifier $22  

Znen 150cc CVT Cover Gasket (Short Version) (fits only the Znen brand of Mopeds) $7

Znen 150cc CVT Cover Gasket (Long Version) (fits only the Znen brand of Mopeds) $7

Znen Sport 150T-18 Muffler $130

 

Znen 150cc CVT Black Cover (Long Version) (fits only the Znen brand of Mopeds) $60

Znen GY6 150cc CDI $23

 

Znen 150cc Timing Chain Guide set (fits only the Znen brand of Mopeds) $12

Znen 150cc Chain Tensioner (fits only the Znen brand of Mopeds) $16

Znen 150cc Camshaft (fits only the Znen brand of Mopeds) $24

 

Znen 150T-18 Cylinder only with gaskets (only fits the Znen 150T-18 scooter) $75

 


Znen 150T-18 Cylinder Kit (only fits the Znen 150-18 scooter) $
100

Znen 150cc Timing Chain (11 inch, 90 Link) (fits only the Znen brand of Mopeds) $12

Znen 150cc 12-Coil Magneto Housing (fits only the Znen brand of Mopeds)$36

 
 Znen GY6 150cc Scooter 12-coil Stator (29mm center hole diameter, 42mm diagonal bolt hole spacing) (fits only the Znen brand of Mopeds) $38

Cheng Shin CST 100/80-16 Moped Tire $72

Duro 120/80-16 Moped Tire $72

Znen 150cc Ignition Coil (fits only the Znen brand of Mopeds) $20

Znen 150cc Ignition Coil (1-prong version) for Znen Brand Motor $20

Znen 150cc Variator (Pulley) (fits only the Znen brand of Mopeds) $40

Znen 150cc Rocker Arm Holder (fits only the Znen brand of Mopeds) $24


GY6 125cc to 150cc Carburetor
$48


Znen 150T-18  150cc Head w/vavles  & gaskets (fits only the Znen 150T-18 Moped motor) $
78

Znen 150cc CVT Silver Cover (Long Version) (fits only the Znen brand of Mopeds) $60

 

Znen 150cc Crankshaft (fits only the Znen brand of Mopeds) $69

 

Break Hose Screw 10mmx29mm $2

 

Moped Stock Fuel Filter $2.50 

 GY6 125cc/150cc Vacuum Fuel Pump (stock)  $30

 GY6 Fuel  Valve $12

KOSO HP  28mm Carburetor kit (for GY6 Mopeds) $130

4-stroke Carburetor Bowl Gasket $2.70 each 

 Znen 150T-18 GY6 150cc Clutch Assembly $89

GY6 125cc/150cc Air Filter $20

 GY6 125/150cc Manifold  (30mm diameter rubber part, 22mm diameter metal intake) (1 outlet) $15

 GY6 125/150cc Manifold  (30mm diameter rubber part, 22mm diameter metal intake)  (2 outlet) $15

GY6 125cc/150cc manifold (rubber part 30mm diameter, metal intake 22mm diameter) (2 outlet, Extended Version) $20


GY6 125/150cc Turbo Fan $29 
 GY6 cvt belt (835-20-30) $26

znne 150T-18 bare head
Znen 150T-18 Bare Head w/gaskets (no valves included) $58

GY6 125cc-150cc Performance Jet Set  ver. #1  $8


GY6 HP Manifold (Aluminum intake 27mm/ Rubber intake 32mm ) $36

 GY6  50cc to 150cc Dipstick (8.2cm long) $8

GY6 125cc/150cc Red Cooling Fan $20

Jonway 150T-2 Hydraulic Brake Pad set (fits front & Rear brake) also Fits Znen 150T-18 rear brake $10
 

Repair Kit for GY6 125/150cc Carburetor $1
0

GY6 120cc/150cc Kick Starter Idle Gear $20

GY6 125/150cc Counter Shaft Gear $40

GY6 150cc Oil Pump Chain $10

GY6 125cc-150cc Final Drive Gear (51Tooth/19Tooth) $20


CVK GY6 125cc-150cc Performance Jet Set  ver #2  (main jet #115, Idle Jet#38.   $9.50
           

Battery Strap (5 Inch Long)  $2.50

 GY6 125cc/150cc Isolater (23mm center hole, 45mm bolt hole spacing)  $4

GY6 150cc Cylinder Gasket $8


 GY6 Solenoid  $14   

 4-Stroke Battery (12v,9AH ) Acid Insert style $42
 

 


GY6 125cc to 150cc Starter  $5

 Iridium Performance Spark Plug (CR8HIX) $17

NGK Racking Cable (CR2) $29   

GY6 125cc/150cc motor Stock Ignition Coil  $18  

GY6 Billet Dip Stick (7.8cm) $20 


 GY6 Stock Spark Plug (50cc to 150cc) $2.50

HP Ignition Coil for GY6 motors  50cc to 150cc motor $29  

GY6 125cc/150cc Final Drive Shaft (version 1, 19 Splines, 194mm length, Diameter at Bearing End: 26mm, Diameter at Smooth End: 16mm) $23

GY6 125cc/150cc Final Drive Shaft (version 2, 19 Splines, 196mm length, Diameter at Bearing End: 26mm, Diameter at Smooth End: 16mm) $23

ABS Upgrade (10mm tread) $16

 906-22.5-30 Belt 

CVK GY6 125cc-150cc Performance Jet Set  ver #3  (main jet #122, Idle Jet#42) recommended for big bore kits  $9.50

GY6 150cc Performance Roller Weight set (9g, 10g or 11g set) $20 per set

 GY6 150cc Gasket set $16

 Electric Choke for GY6 125cc/150cc Carburetors $10 

GY6 125cc/150cc Rear Drive Shaft (Version 1) (173mm) $28

GY6 125cc/150cc Rear Drive Shaft (Version 2) (186mm) $28

GY6 150cc Starter Clutch Assembly (50Tooth) $36


 GY6 Fuel  Valve $16 
           

 GY6 150cc Piston Rings set (57mm) $12

GY6 150cc Oil Pump $20

GY6 50cc-150cc Muffler Screw Set (6mm) $6


 GY6 150cc Valve set $18

GY6 150cc Piston Rebuilt Kit (57mm diameter, 15mm wrist pin)  $37  
 
 GY6 125cc/150cc HP  Camshaft $59

4-Stroke 42mm Shielded Air Filter (fit's GY6 125cc/150cc motors) $20  

GY6 125cc/150cc Valve Assembly $26
GY6 150cc Clutch Shoe Set
 GY6 150cc Clutch Shoe Set $25

 GY6 125cc/150cc Koso HP Pulley $50
gy6 4-way fuel valve
GY6 Mini 4-Way Remote Fuel Valve
 

GY6 Mini 3-Way Remote Fuel Valve $13 
 
 
 GY6 150cc Head Bolt each $4, or  $13 for set 4

Znen Neck/Bearings (Set of 7 - 50mm, 44mm, 43mm, 43mm, 40mm, 36mm, 31mm) $16  


  GY6 125cc/ 150cc Kick Start Gear Shaft (spindle) Version 1, 130mm total length $20

 GY6 125cc/ 150cc Kick Start Gear Shaft (spindle) Version 2, 170mm total length $20

GY6 125cc/150cc Crank Bearing $11 

GY6 Moped 150cc Discharge Resistance $20

 


 GY6 125cc/150cc HP Clutch Spring set (1000 RPM) $10

 GY6 125cc/150cc HP Clutch Spring set (1500 RPM) $10

 GY6 125cc/150cc HP Clutch Spring set (2000 RPM) $10

  Moped Red Rectangle Reflector $4

  4-Stroke Fuel Line  $1.40 per Foot

 GY6 125cc/150cc HP Clutch Drum (Bell) $49

flywheel puller

Universal Flywheel Puller (for Moped, ATV, & Dirt bikes) $29

Moped Master Cylinder with Mirror Holder (Skinny, Black Color, Left Side) 53mm L X 64mm H X 28mm W $20


 GY6 150cc Fan Cover $6


GY6 50cc to 150cc 30.50mm Exhaust Gasket  $2

 

GY6 150cc Valve Cover Gasket $3

 

GY6 39mm Crank Tool $16

GY6 50cc-250cc Clutch Tool(39mm/41mm) $24


Moped Chrome Mirror Set (10mm) $40

 4-Stroke Performance Fuel Line (Yellow or Green) $8

Wire Tie (30 set) $2, 300 set $14 
 
TreadLocker (Med Strength, 50 Gram)

Moped Kill Switch (4 Wire Plug) $5

Moped Horn Switch (2 Wire Plug) $5

Moped Passing Switch (4 Wire Plug) $5

Moped Turn Signal Switch (6 Wire Plug) $5

Moped Light Switch (6 Wire Plug) $5

Moped Starter Switch (2 Wire Plug) $5

Moped High/Low beam switch 3- Wire Plug) $5


Moped Chrome Mirror Set (8mm) $40 

Moped Chrome Round Mirror Set (8mm) $28

 Tire Popper Tool  $38

 GY6 Kick Starter (Flat Pedal Version) $16 
 
 GY6 Kick Starter (Round Pedal Version) $14

Moped Blank Key set ( Ver. #1)  $5
 
Moped Blank Key set ( Ver. #2)  $5

Moped Blank Key set ( Ver. #3)  $5
 
Moped Blank Key set ( Ver. #4)  $5

Moped Blank Key set: foldable ( Ver. #5)  $5
 
  Moped Orange Round Reflector $4
             
            ScooterParts4Less 

  border=0>